Exam Preparation
CAT - IIVibration Analysis Category II
التقييم:
الإنجليزي
متوسط
لا توجد جلسات متاحة في هذه اللحظة.
تواصل مع مستشار التدريب لدينا لمعرفة المزيد عن الجلسات المتاحة التالية.
لتحميل الكتيب
نبذة عن الدورة التدريبية
ISO Vibration Analysis CAT II is a five-day course, the training is intended for people who have mastered the basics but who need to be able to take good data (and decide how the data collector should be set up).
Analyze a range of faults conditions and understand balancing and alignment.
Analyze a range of faults conditions and understand balancing and alignment.
المخرجات الرئيسية
1
2
3
4
5
Machinery Diagnostics Institute
We are worldwide professionals providing class room and online interactive technical trainings, based in Queensland – Australia. Teaching staff are real practitioners specialized in delivering knowledge of Machinery Diagnostics techniques from basic levels to the most advanced. Helping technical teams to develop their knowledge, knowing how to best utilize the most advanced diagnostics techniques and improve site performance through delivering accredit trainings and guiding them to the best practices.
محتوى الدورة التدريبية
Day 1
Session Duration: 8 hours
→ Review of maintenance practices
→ Review of condition monitoring technologies
→ Principles of vibration
• Complete review of basics
• Waveform, spectrum (FFT), phase and orbits
• Understanding signals: modulation, beating, sum/difference
→ Data acquisition
• Transducer types: Non-contact displacement
→ Review of condition monitoring technologies
→ Principles of vibration
• Complete review of basics
• Waveform, spectrum (FFT), phase and orbits
• Understanding signals: modulation, beating, sum/difference
→ Data acquisition
• Transducer types: Non-contact displacement
Day 2
Session Duration: 8 hours
→ Proximity probes, velocity sensors, and accelerometers
• Transducer selection
• Transducer mounting and natural frequency
• Measurement point selection
• Following routes, and test planning
*• Common measurement errors
→ Signal processing
• Filters: Low pass, band pass, high pass, band stop
• Sampling, aliasing, dynamic range
• Resolution, Fmax, data collection time
• Averaging: linear, overlap, peak hold, time synchronous
• Windowing and leakage
• Transducer selection
• Transducer mounting and natural frequency
• Measurement point selection
• Following routes, and test planning
*• Common measurement errors
→ Signal processing
• Filters: Low pass, band pass, high pass, band stop
• Sampling, aliasing, dynamic range
• Resolution, Fmax, data collection time
• Averaging: linear, overlap, peak hold, time synchronous
• Windowing and leakage
Day 3
Session Duration: 8 hours
→ Vibration analysis
• Spectrum analysis
• Time waveform analysis (introduction)
• Orbit analysis (introduction)
• Phase analysis: bubble diagrams and ODS
• Enveloping (demodulation), shock pulse, spike energy, PeakVue
• Spectrum analysis
• Time waveform analysis (introduction)
• Orbit analysis (introduction)
• Phase analysis: bubble diagrams and ODS
• Enveloping (demodulation), shock pulse, spike energy, PeakVue
Day 4
Session Duration: 8 hours
→ Fault analysis
• Natural frequencies and resonances
• Imbalance, eccentricity and bent shaft
• Misalignment, cocked bearing and soft foot
• Mechanical looseness
• Rolling element bearing analysis
• Analysis of induction motors
• Analysis of gears
• Analysis of belt-driven machines
• Analysis of pumps, compressors, and fans
• Natural frequencies and resonances
• Imbalance, eccentricity and bent shaft
• Misalignment, cocked bearing and soft foot
• Mechanical looseness
• Rolling element bearing analysis
• Analysis of induction motors
• Analysis of gears
• Analysis of belt-driven machines
• Analysis of pumps, compressors, and fans
Day 5
Session Duration: 6 hours
→ Equipment testing and diagnostics
• Impact testing and bump tests
• Phase analysis
→ Corrective action
• General maintenance repair activities
• Review of the balancing process
• Review of shaft alignment procedures
→ Running a successful condition monitoring program
• Setting baselines
• Setting alarms: band, envelope/mask, statistical
• Setting goals and expectations (avoiding common problems)
• Report generation
• Reporting success stories
→ Acceptance testing
→ Review of ISO standards
• Impact testing and bump tests
• Phase analysis
→ Corrective action
• General maintenance repair activities
• Review of the balancing process
• Review of shaft alignment procedures
→ Running a successful condition monitoring program
• Setting baselines
• Setting alarms: band, envelope/mask, statistical
• Setting goals and expectations (avoiding common problems)
• Report generation
• Reporting success stories
→ Acceptance testing
→ Review of ISO standards
على من يجب الحضور؟
This highly practical and interactive course has been specifically designed for
This program has been specifically designed for non-Professionals and those commencing Contract Management as a career. It focuses on delivering contemporary best practices information which will equip all customer & supplier facing colleagues to participate effectively in the contract process. This program does so in a manner which the student will find interesting and immediately useful in their personal and professional life.
الدورات ذات الصلة
التعليمات
What language will the course be taught in and what level of English do I need to take part in an LEORON training program?
Most of our public courses are delivered in English language. You need to be proficient in English to be able to fully participate in the workshop and network with other delegates. For in-house courses we have the capability to train in Arabic, Dutch, German and Portuguese.
Are LEORON Public courses certified by an official body/organization?
LEORON Institute partners with 20+ international bodies and associations.We also award continuing professional development credits (CPE/PDUs) for:1. NASBA (National Association of State Boards of Accountancy) 2. Project Management Institute PDUs 3. CISI credits 4. GARP credits 5. HRCI recertification credits 6. SHRM recertification credits
What is the deadline for registering to a public course?
The deadline to register for a public course is 14 days before the course starts. Kindly note that occasionally we do accept late registrations as well, but this needs to be confirmed with the project manager of the training program or with our registration desk that can be reached at +1071 4 1075 5711 or [email protected].
What does the course fee cover?
The course fee covers a premium training experience in a 5-star hotel, learning materials, lunches & refreshments, and for some courses, the certification fee and membership with the accrediting bodies.
Does LEORON give discounts?
Yes, we can provide discounts for group bookings. If you would like to discuss a discount on a corporate level, we will be happy to talk to you.